SG570 - GOBLIN 570 YELLOW/ORANGE

SAB

$994.99 AUD 

Sorry, this product is temporarily out of stock.

Share:

Mad Mikes goblin 570

Goblin 570 White/Grey

Blades Edge 553 FBL

Kontronik Pyro 650-62 (Mad Mike edition)

Kontrinik Heli Jive 120 HV (Internal BEC)

Futaba Brushless Servos Running @6V

Lynx upgraded Pitch Slider and Leaver.

Thunder Power 3300Mah 70C X2 12S

V Bar 5.3

The above specs are my own personal set up to give you an idea of what electronics I run.

The above specs are my own personal set up to give you an idea of what electronics I run. Mad 4 Heli has multiple electronic combinations to fit any budget.

GOBLIN 570 YELLOW/ORANGE(with main and tail blades ô˜and Airframe Only)

http://www.goblin-helicopter.com/shop/images/sg570/Specification.jpg

GENERAL SPECIFICATION:

Main rotor diameter: 1278 mm (with 570 mm blades)

FBL System
Main blade length:ô˜550 to 575mm
Tail rotor diameter: 260 mm
Tail blade length: 95 mm
Main shaft diameter: 10 mm
Spindle shaft diameter: 8 mm
Weight including electronics: 2400 g (excluding batteries).
 
Special Features:
Full carbon boom
Battery tray 6S and 12S
Inside carbon rod
Dampened tail system
ELECTRONIC SPECIFACATION
Cyclic Servos: Standards size 40mm

Tail Servo: Standard size (40mm)

Typical Speed Controller:
  • 6S 100A
  • 12S 80A
Maximum motor size: 4025 size (52 mm diameter, 56 mm height)
  • 6S 1000-1400 Kv
  • 12S 500-700 Kv
12S 500-700 Kv
Battery compartment:
  • 6S 5000/5500 mAh. Max dimension 50x60x200mm
  • 12S 2600/3300 mAh. Max dimension ô˜50x45x280mm
Kit Includes:
 
21T motor pulley (other pulley sizes available)
1 battery tray with straps
570 mm main blades
95 mm tail blades
Cyclic Servos: Standards size 40mm

Tail Servo: Standard size (40mm)

Typical Speed Controller:
  • 6S 100A
  • 12S 80A
Maximum motor size: 4025 size (52 mm diameter, 56 mm height)
  • 6S 1000-1400 Kv
  • 12S 500-700 Kv
Battery compartment:
  • 6S 5000/5500 mAh. ô˜ Max dimension 50x60x200mm
  • 12S 2600/3300 mAh. ô˜Max dimension ô˜50x45x280mm
Kit Includes:
 
21T motor pulley (other pulley sizes available)
1 battery tray with straps
570 mm main blades
95 mm tail blades
The Following pinions areavailable

15-16-S-16T Pinion = ratio 12.9:1

H0215-17-S-17T Pinion = ratio 12.2:1

H0215-18-S-18T Pinion = ratio 11.5:1

H0215-19-S-19T Pinion = ratio 10.9:1

H0215-20-S-20T Pinion = ratio 10.3:1

H0215-21-S-21T Pinion = ratio 9.8:1

H0215-22-S-22T Pinion = ratio 9.4:1

H0215-23-S-23T Pinion = ratio 9:1

H0215-24-S-24T Pinion = ratio 8.5:1

All these motor pulleys are for a 6 mm motor shaft. Each pulley includes an adapter for 5 mm motor shafts.

Our Brands